Cabinets for these chassis available here.



Features and Options for Weber Chassis Products
Chassis

High quality 16ga sheet steel, stainless steel, or .090" Aluminum
Extra fine buffing, heavy nickel and chrome plating
Special screen lettering paint resists chemicals and abrasion
All lettering centered properly and aligned with control layout
Chassis kit includes brass grounding plate and, unless otherwise noted, black fiber eyelet board set
Quantity discounts available
Brass Grounding Plate

Precisely punched with no material mounding or shearing around hole.
Fiber Eyelet Board

Dense paper laminate with high dielectric strength and moisture resistance to prevent 'Tweed' disease.
Routed and machined on CNC milling machines for clean edges and perfectly aligned
     holes.
All eyelets retinned for ease of soldering.
Additional Information

Please Note: Our chassis products may require some modifications for a particular application, such as accommodating the transformers and chokes to be used. Accordingly, these chassis products are best suited for experienced amp builders who have the necessary knowledge and tools to effect the modifications.

And, on a final note, after selling chassis for over 12 years now, we have given up on chromers and platers. I don't know if it is the EPA, pay scale, or a combination of several factors, but we have had nothing but trouble getting decent chroming on our chassis. In many cases, we had more scrap than we had chasses we could sell. For awhile, we were selling chassis at a net loss just to be able to have them available for our kits and other uses. Very frustrating. So, we recently made the inevitable decision to go with stainless steel chasses exclusively. We are using the highest polished steel that actually looks better than the best chromed chassis we had. Secondly, we are putting weld studs in all chassis to allow for the establishment of a single point ground. I had two amps built identically, one with our traditional chassis and one with stainless. I blueprinted them, meaning I used the same set of tubes for testing each and made all voltages identical in both amps. At that point, I could do a reliable test for noise comparisons between the two. I did that because a lot of people poo-poo stainless steel chasses. I found they both had virtually identical noise floors, and their signal to noise ratios were essentially the same at many different volume settings. So, I'm convinced we're moving in the right direction, and I hope you will too.

Please Note: For blank chassis, please visit PM Sound Technology or Turretboards.com

 9 Pin Shock Mount

 
Tube socket and shield not included

Shock mount device for preamp tubes to help prevent chassis-induced vibration
         noises. May also be used for 9 pin output tubes.
 Includes shock plate, grommets, springs, and #4 mounting hardware.
         9 pin socket ID is 3/4", mounting ear holes center to center is 1-1/8".

Quantity     SM9 9 Pin Shock Mount...............$6.00
 

 

 AP1

 

Universal adapter plate to convert octal socket hole to accept 9 pin socket.
 Laser cut and trimmed, O.D. is 1-3/4", octal mounting ear holes center to center is 1-1/2".
 9 pin socket ID is 3/4", mounting ear holes center to center is 1-1/8".

Quantity     AP1 Adapter Plate...............$5.00
 

 

 CP8

 

Universal cover plate for unused octal socket hole.
Laser cut and trimmed, O.D. is 1-3/4", octal mounting ear holes center to center is 1-1/2".

 

Quantity     CP8 Cover Plate...............$5.00
 

 

 CP9

 


Universal cover plate for unused 9 pin socket hole.
Laser cut and trimmed, O.D. is 1-3/8", 9 pin mounting ear holes center to center is 1-1/8"

 

Quantity     CP9 Cover Plate...............$5.00
 

 

 Terminal Boards

 


That four-eyelet black terminal board used as a tie-point for multi speaker cabinets.
Black fiber board, 1/8" center hole, 4 equally spaced perimeter holes.
TB1 Terminal Board has two eyelets and two 1/4" holes.
TB2 Terminal Board has four eyelets.

 

Quantity     TB1 Terminal Board...............$4.00
Quantity 
   TB2 Terminal Board...............$4.00
 


 

 5G15 (Chrome-faced Reverb)



(click to enlarge)

Tweed style, 1 octal, 2-9 pin socket holes
Mix, Dwell, Tone, Power, Pilot Light, Fuse, IN/OUT & footswitch jack holes.
 

Quantity     5G15 Chassis Kit...................$90.00
Quantity     5G15 Chassis Only................$70.00
Quantity     Fiber Board Set Only.............$12.00
Quantity     Brass Grounding Plate Only......$12.00
 

 

 5H15 ReVibe



(click to enlarge)

Tweed style, 1 octal, 4-9 pin socket holes
Reverb Mix, Dwell, Tone, Vibrato Intensity, Speed, Power, Pilot Light, Fuse,
     IN/OUT & footswitch jack holes.
Chassis is set up for 3 tube Vibrato and 3 knob Reverb.
 

Please Note: This chassis is unique and is not a copy of a vintage model. The fiber board includes eyelets arranged for the components used in the common three knob reverb and the three tube vibrato. You should have a good understanding of the operation of both circuits and their implementation before purchasing this chassis.

Quantity     5H15 Chassis Kit...................$90.00
Quantity     5H15 Chassis Only................$70.00
Quantity     Fiber Board Set Only.............$12.00
Quantity     Brass Grounding Plate Only......$12.00
 

 

  5F1



(click to enlarge)

Tweed style, 2 octal, 1-9 pin socket hole
1 Channel, 2 Inputs, ON-OFF/Volume, Fuse, Pilot Light
 

Quantity     5F1 Chassis Kit..............$80.00
Quantity     5F1 Chassis Only................$60.00
Quantity     Fiber Board Set Only.............$12.00
Quantity     Brass Grounding Plate Only......$12.00
 

 

  5F2A



(click to enlarge)

Tweed style, 2 octal, 1-9 pin socket holes
1 Channel, 2 Inputs, Volume, Tone, Power, Fuse, Pilot Light
 

Quantity     5F2A Chassis Kit..............$85.00
Quantity     5F2A Chassis Only................$65.00
Quantity     Fiber Board Set Only.............$12.00
Quantity     Brass Grounding Plate Only......$12.00
 

 

  5E3



(click to enlarge)

Tweed style, 3 octal, 2-9 pin socket holes
2 Channel, 2 Inputs per channel, 2 Volume, Tone, Power, Fuse,
     Standby, Pilot Light
Original GROUND switch lettering replaced with STANDBY
 

Quantity     5E3 Chassis Kit..............$100.00
Quantity     5E3 Chassis Only................$80.00
Quantity     Fiber Board Set Only.............$12.00
Quantity     Brass Grounding Plate Only......$12.00


 

 

  5E3x2



(click to enlarge)

Tweed style, 5 octal, 2-9 pin socket holes
2 Channel, 2 Inputs per channel, 2 Volume, Tone, Power, Fuse,
     Standby, Pilot Light
Original GROUND switch lettering replaced with STANDBY
 

Quantity       5E3x2 Chassis Kit..............$110.00
Quantity       5E3x2 Chassis Only................$90.00
Quantity     Fiber Board Set Only.............$12.00
Quantity     Brass Grounding Plate Only......$12.00
 

 

  5C3



(click to enlarge)

Tweed style, 5 octal, (2 pre's, 2 outputs, 1 recto)
2 Channel, 2 Inputs per channel, 2 Volume, Tone, Power, Fuse,
     Standby, Pilot Light
Original GROUND switch lettering replaced with STANDBY
 

Quantity     5C3 Chassis Kit..............$100.00
Quantity     5C3 Chassis Only................$80.00
Quantity     Fiber Board Set Only.............$12.00
Quantity     Brass Grounding Plate Only......$12.00
 

 

  5C5



(click to enlarge)

Tweed style, 6 octal (three pre's, two outputs, 1 recto)
2 Channel, 2 Inputs per channel, 2 Volume, Tone, Power, Fuse,
     Standby, Pilot Light
Original GROUND switch lettering replaced with STANDBY
 

Quantity     5C5 Chassis Kit..............$110.00
Quantity     5C5 Chassis Only................$90.00
Quantity     Fiber Board Set Only.............$12.00
Quantity     Brass Grounding Plate Only......$12.00
 

 

  5F4 / 5E5 / 5E7


5E7  5E7M
(click to enlarge)

Standard 5E7 chassis:
Tweed style, 3 octal, 3-9 pin socket holes
2 Channel, 2 Inputs per channel, 2 Volume, Bass, Treble, Presence, Power, Fuse,
    Standby, Pilot Light, Ground

5E7M Chassis: (middle control instead of presence)
Tweed style, 3 octal, 3-9 pin socket holes
2 Channel, 2 Inputs per channel, 2 Volume, Bass, Middle, Treble, Power, Fuse,
    Standby, Pilot Light, Ground
 

Quantity     5E7 Chassis Kit..............$110.00
Quantity     5E7 Chassis Only................$90.00
Quantity     5E7M Chassis Kit..............$110.00
Quantity     5E7M Chassis Only................$90.00
Quantity     Fiber Board Set Only.............$12.00
Quantity     Brass Grounding Plate Only......$12.00
 

 

  5F6



(click to enlarge)

Tweed style, 3 octal, 3-9 pin socket holes
2 Channel, 2 Inputs per channel, 2 Volume, Bass, Middle, Treble, Presence, Power,
     Fuse, Standby, Pilot Light, Ground
 

Quantity     5F6 Chassis Kit..............$120.00
Quantity     5F6 Chassis Only................$100.00
Quantity     Fiber Board Set Only.............$12.00
Quantity     Brass Grounding Plate Only......$12.00
Quantity     Large Capacitor Board Only......$6.00
 

 

  5E8A



(click to enlarge)

Tweed style, 4 octal, 4-9 pin socket holes
2 Channel, 2 Inputs per channel, 2 Volume, Treble, Bass, Presence, Fuse, Power,
    Standby, Pilot Light, Ground
 

Quantity     5E8A Chassis Kit..............$120.00
Quantity     5E8A Chassis Only................$100.00
Quantity     Fiber Board Set Only.............$12.00
Quantity     Brass Grounding Plate Only......$12.00
 

 

  5F8



(click to enlarge)

Tweed style, 5 octal, 3-9 pin socket holes
2 Channel, 2 Inputs per channel, 2 Volume, Treble, Bass, Mid, Presence, Power,
     Fuse, Standby, Pilot Light, Ground
 

Quantity     5F8 Chassis Kit..............$120.00
Quantity     5F8 Chassis Only................$100.00
Quantity     Fiber Board Set Only.............$12.00
Quantity     Brass Grounding Plate Only......$12.00
 

 

  6A14



(click to enlarge)

3 octal, 4-9 pin socket holes, Includes IEC socket
1 Channel, 2 Inputs, In, In, Vol, Treble, Bass, Reverb, Speed, Intensity
 

Quantity     6A14 Chassis Kit..............$125.00
Quantity     6A14 Chassis Only................$90.00
Quantity     Fiber Board Set Only.............$24.00
Quantity     Brass Grounding Plate Only......$12.00
Quantity     6A14 Front panel (faceplate)................$18.00
Quantity     6A14 Rear panel (faceplate)................$12.00
 

 

  6A20



(click to enlarge)

3 octal, 6-9 pin socket holes, Includes IEC socket
2 Channels, 2 Inputs per channel. In, In, Bright Sw, Vol, Treb, Bass, In, In, Bright Sw, Vol, Treb, Bass, Reverb, Speed, Intensity
 

Quantity     6A20 Chassis Kit..............$125.00
Quantity     6A20 Chassis Only................$100.00
Quantity     Fiber Board Set Only.............$24.00
Quantity     Brass Grounding Plate Only......$12.00
Quantity     6A20 Front panel (faceplate)................$20.00
Quantity     6A20 Rear panel (faceplate)................$12.00
 

 

 6A40



(click to enlarge)

3 octal, 6-9 pin socket holes, Includes IEC Socket
2 Channels, 2 Inputs per channel. In, In, Bright Sw, Vol, Treb, Bass, In, In, Bright Sw, Vol, Treb, Mid, Bass, Reverb, Speed, Intensity
 

Quantity     6A40 Chassis Kit..............$125.00
Quantity     6A40 Chassis Only................$100.00
Quantity     Fiber Board Set Only.............$24.00
Quantity     Brass Grounding Plate Only......$12.00
Quantity     6A40 Front panel (faceplate)................$20.00
Quantity     6A40 Rear panel (faceplate)................$12.00
 

 

  6A80



(click to enlarge)

4 octal, 6 - 9 pin socket holes, based on BF Twin.
2 Channels, 2 Inputs per channel.
 

Quantity     6A80 Chassis Kit..............$125.00
Quantity     6A80 Chassis Only................$100.00
Quantity     Fiber Board Set Only.............$24.00
Quantity     Brass Grounding Plate Only......$12.00
Quantity     Snap-In Female Auxiliary Socket......$1.65
Quantity     6A80 Front panel (faceplate)................$20.00
Quantity     6A80 Rear panel (faceplate)................$12.00
 

 

  6M18



(click to enlarge)

6 - 9 pin socket holes.
Acrylic control panel
2 Channel, 2 Volumes, 2 Tones, Intensity, Speed, or TMB
Faceplate and controls standard size and location. Available with Vibrato or TMB lettering and in combo or head version.

The complete kit ($105) includes the chassis, pilot lamp lens, brass plate, fiber board, and plexi panel.
 
Qty Price Click For Image Pilot Lamp Color Buy
  $ 115.00    6M18 Kit
Combo TMB
Combo Vibrato
Head TMB
Head Vibrato
  $ 85.00   6M18 Chassis Only
(Includes faceplate)
Combo TMB
Combo Vibrato
Head TMB
Head Vibrato
  $ 18.00   6M18 Fiber Board  
  $ 12.00   6M18 Brass Plate  
  $ 20.00   6M18 Combo Plexi Faceplate
Combo TMB
Combo Vibrato

Front Only

  $ 40.00   6M18 Head Plexi Faceplates
Head TMB
Head Vibrato

Front and Rear

 

  6M36


(click to enlarge)

7 - 9 pin socket holes, 1 octal socket hole.
Acrylic control panel
2 Channel. Channel 1: Volume, Tone. Channel 2: Volume, Treble, Middle, Bass
Faceplate and controls standard size and location. Available in a head or combo version.

The complete kit ($105) includes the chassis, pilot lamp lens, brass plate, fiber board, and plexi panel.
 
Qty Price Click For Image Pilot Lamp Color Buy
  $ 115.00    6M36 Kit
Combo
Head
  $ 85.00   6M36 Chassis Only
(Includes faceplate)
Combo
Head
  $ 18.00   6M36 Fiber Board  
  $ 12.00   6M36 Brass Plate  
  $ 20.00   6M36 Combo Plexi Faceplate

Front Only

  $ 40.00   6M36 Head Plexi Faceplates

Front and Rear

  6M50



(click to enlarge)

9 - 9 pin socket holes, 2 octal socket holes.
Acrylic control panel
2 Channel, 2 Volumes, Treble, Middle, Bass
Faceplate and controls standard size and location.

The complete kit ($105) includes the chassis, pilot lamp lens, brass plate, fiber board, and plexi panels.
 
Qty Price Click For Image Pilot Lamp Color Buy
  $ 115.00    6M50 Kit
  $ 85.00   6M50 Chassis Only
(Includes TMB faceplate and rear plate)
  $ 18.00   6M18/50 Fiber Board  
  $ 12.00   6M18/50 Brass Plate  
  $ 40.00   6M50 Plexi Faceplates

Front and Rear

 

  6M45



(click to enlarge)

3 octal, 3-9 pin socket holes.
Gold-backed plexi control and back panels, .090" aluminum chassis
2 Channel, 2 Inputs per channel, 2 Volumes, Bass, Mid, Treble, Presence
Faceplate, controls and backplate standard size and location.


The complete kit ($110) includes the chassis, pilot lamp lens, brass plate, fiber board, and plexi panels.
 
Qty Price Click For Image Pilot Lamp Color IEC Power Socket Buy
  $ 120.00    6M45 Kit $1.65
Yes
No
  $ 100.00   6M45 Chassis Only    
  $ 12.00   6M45 Fiber Board Set    
  $ 12.00   6M45 Brass Plate    
  $ 40.00   6M45 Plexi Faceplates

Front and Rear

 

 

  6M100



(click to enlarge)

4 octal, 3-9 pin socket holes. Quad and Single Cap Can openings, PT, OT, and Choke layouts same as original.
Gold-backed plexi control and back panels, .0625" steel chassis
2 Channel, 2 Inputs per channel, 2 Volumes, Bass, Mid, Treble, Presence
Faceplate, controls and backplate standard size and location.
Includes 6 cutouts in chassis for LCR-type multisection filter capacitors.


The complete kit ($110) includes the chassis, pilot lamp lens, brass plate, and plexi panels.

Note: There is no fiber board set for this chassis kit.

 
Qty Price Click For Image Pilot Lamp Color IEC Power Socket Buy
$130.00 6M100 Kit Included
$105.00 6M100 Chassis Only
(Includes faceplates)
   
$12.00 6M100 Brass Plate      
  $ 40.00   6M100 Plexi Faceplates

Front and Rear

 

 

 

  6Mx



(click to enlarge)

4 octal, 2-9 pin socket holes.
.090" aluminum chassis
1 Channel, 2 Inputs, Nine 3/8" control holes, PWR, STBY, Pilot Lamp

Generic 50 to 100 watt head chassis. Same size as a standard '45 chassis. Standup PT and OT with large grommet holes to fit just about any transformer wiring. PT and OT foot mounting holes are slotted. Also includes mounting for choke. Mounting holes provided for 2-1/2" by 10" fiber board. Output tube socket holes are positioned to accept 6L6's, 6V6's, EL34's, KT66's, and KT88's.  NO FACEPLATES

Pictures coming soon

Qty Price Click For Image IEC Power Socket Buy
  $ 30.00   6Mx Chassis Only
No Fibers, no Panels

$1.65
Yes
No

 

  6SX



(click to enlarge)

4 octal, 5-9 pin socket holes
1 Channel with Bright/Normal, Clean/Crunch, and Overdrive/Normal switches, Normal and Overdrive Preamp Level controls, Bass, Middle, Treble, Normal and Overdrive Master Level controls, Presence, Depth, Standby, Pilot, and Power.
Rear Panel: IEC, mains fuse, B+ fuse, 2 speaker jacks, 4, 8, 16 Z select, Effects S/R, Footswitch
Chassis is powdercoated white with black lettering.

Please note this chassis now has the tube socket mounting ear holes and the transformer mounting holes punched.  The transformer mounting will accommodate our WPT100 and WOT100.

Note: There is no fiber board set for this chassis kit.
 

Quantity     6SX Chassis Kit..............$100.00
Quantity     6SX Chassis Only................$90.00
Quantity     Brass Grounding Plate Only......$14.00
Quantity     IEC Socket......$1.65
 

 

  6S100 / 8CM100



(click to enlarge)

5 octal, 4-9 pin socket holes. Chassis is 22" x 7.5" x 2.5"
Aluminum Chassis used for the 6S100 and 8CM100 amp kits. Two input jacks, Eight controls, Power, Standby, Pilot lamp hole (for MPL lamp)
Rear Panel: IEC, mains fuse, B+ fuse, 2 speaker jacks, Impedance select, four Bias adjust, two bias test holes
The transformer mounting will accommodate our WPT100 and WOT100HHR or LHR, w022699 Choke.


6S100 panels are silver with black letters. 8CM100 panels are gold with black letters. See our amp kits page for details on these kits.

 

Quantity     6S100 Chassis Kit..............$100.00
Quantity     8CM100 Chassis Kit..............$100.00
Quantity     6S100 Chassis Only................$90.00
Quantity     IEC Socket......$1.65
 

 

  6V30



(click to enlarge)

1 octal, 10-9 pin socket holes for 4-EL84 application.
3 Channels (1 Normal, 1 Brilliant, 1 Vib-Trem), 3 Volumes, Bass, Treble, Cut, Power,
     Pilot Light, Fuse, Standby
Preamp chassis is aluminum, power amp chassis is steel.

 
Qty Price Click For Image Pilot Lamp Color Panel Background Color Buy
  $ 140.00    6V30 Kit
  $ 120.00   6V30 Chassis Only
  $ 12.00   6V30 Fiber Board Set    
  $ 14.00   6V30 Brass Plate    


 

  Smokin' Joe


  
(click to enlarge)

Four 9 pin socket hole
1 Channel, 1 Input, ON-OFF/Volume, Tone, Master, Fuse(rear), Pilot Light
 

Quantity     Smokin' Joe Chassis Kit..............$90.00
Quantity     Smokin' Joe Chassis Only................$70.00
Quantity     Fiber Board Set Only.............$12.00
Quantity     Brass Grounding Plate Only......$12.00
 

 

 

 


Content © 1998-present Weber Vintage Sound Technology
Soldano is a trademark of Soldano Amps. Bandmaster and Vibrolux are trademarks of Fender.